Monthly Archives: May 2020

Dynamic Carrier for Contact

Posted on by
Reply

Many of the tools that build presets on this site will create optimized presets for Contact, where a dynamic carrier wave is used to get deeper penetration of the frequency, and to make low frequencies less painful. This is described in a previous post: Optimizing Contact and Plasma Presets. This current post offers both an online and an offline tool you can use to convert your presets to use this dynamic carrier wave technique.

This tool runs in a browser window. When you load the tool into the browser, you see the Make Carrier tool below.

Continue reading →

Spooky2’s Analyze Function

Posted on by
Reply

For some time now, when you do a biofeedback scan with GeneratorX or Spooky Pulse, all the colllected scan data is stored in a raw scan data file. For the GeneratorX, this collected scan data includes the Current, Angle, and Angle + Current data. For the Spooky Pulse, this collected scan data includes the BPM (Beats Per Minute) and the HRV (Heart Rate Variability) data. Using the Analyze button, Spooky2 can open these old raw scan data files, and analyze the scan data to give you the top hits in that scan, with any of the data parameters that were saved during that scan.

Continue reading →

Change Hardware for a Preset

Posted on by
Reply

One question that comes up often is “how can I change the hardware for my existing preset?” For for example, let’s say you have a preset for contact that you want to run on plasma. Or here’s a real-world example. If you look in Spooky2 under the Presets tab for ear infection, you see the following. There is a preset for Contact, Plasma, Remote, and Cold Laser, but not one for Scalar. So how can I get a scalar version of the Ear Infection preset?

Continue reading →

Optimizing Contact and Plasma Preset

Posted on by
Reply

There are optimizations of Contact and Plasma presets that are employed by BFBTool, CancerTool, LymeTool, and Morgellons and Lyme Graded Utility that you will enjoy when using these tools. These 4 tools involve building presets from your biofeedback scan results in the context of various protocols. But you can also take your existing presets and employ these same optimization by using the same techniques, or using the BFBTool to optimize your presets.

Plasma Optimizations

For Plasma, if you have frequencies that are over 100 KHz, the best plasma shell preset to use is Spooky Plasma Advanced (P) – JW. This preset give the strongest plasma signal for these higher frequencies. For frequencies lower than 100 KHz, the best plasma shell preset to use is Spooky Plasma Entrainment and Healing (P) – JW. This presets uses beat frequencies, where the difference between the Out 1 and Out 2 frequency is the low frequency, to deliver frequencies that are too low to light up the plasma bulb. Other Rife solutions use amplitude modulation of a fixed carrier wave, but the Spooky approach delivers a stronger signal while not exposing you to frequency fatigue from using a fixed carrier wave.

Continue reading →

Making a Low Power Terrain Preset

Posted on by
Reply

In an earlier post Low Power Terrain Presets, you could download presets for a low power Terrain protocol preset, which is useful for people who are too sensitive to bear the detox and herxing that they experience with the normal Terrain protocol preset. Using ChainEditor, you will learn how you can make your own low power preset with the Amplitude that works best for you.

If you haven’t already, If you haven’t already, install ChainEditor as described in Installing ChainEditor. Double-click the ChainEditorTool icon on the desktop to start ChainEditor.

Continue reading →

Installing ChainEditor

Posted on by
Reply

Before you install ChainEditor, you must have .NET Framework 3.5 installed. The installer for ChainEditor is provided by the Spooky2 installer, and is found in the C:\Spooky2 folder. using the Windows File Explorer, go to your the C:\Spooky2 folder by finding This PC in the left column of the Windows File Explorer, then scrolling down the left column until you find the C: drive, which by default is labeled Local Disk (C:). Your hard drive may be named something else besides Local Disk if you or someone else changed the name of the hard drive. Click Local Disk (C:) on the left column, and scroll down the right column until you find the Spooky2 folder.

Continue reading →

Morgellons and Lyme Graded Utility Guide

Posted on by
Reply

The Morgellons and Lyme Graded Utility (and protocol that it provides) improves the effectiveness of the existing Morgellons and Lyme protocol by grading frequency sets via biofeedback. By grading each part of the Morgellons and Lyme protocol, the most important frequencies of each section are run, thereby reducing the number of frequencies run and eliminating the frequencies that may not apply to your particular condition. This means the important frequencies specific to you get more run time as compared with running all the Morgellons and Lyme frequencies.

The grading of each part of the Morgellons and Lyme protocol is not done via using a grading preset, but rather by using a full system scan and evaluating a set of frequencies from a grading preset against the results of the full system scan to determine the effectiveness of a particular frequency in the protocol section.

Before you start this protocol, you must run the Terrain protocol documented in the Presets tab of Spooky2 in \Detox\GUIDE Terrain Protocol – Click Me.pdf. We recommend using the Contact, Plasma, Scalar, Laser, or Coil presets in addition to the Remote presets for the Terrain protocol to increase the effectiveness of the protocol.

The Morgellons and Lyme Graded protocol is broken into 9 sections, starting from the smallest organisms to the largest. These sections are called Viruses, Biofilm, Co-infection, Other Bacteria, Fungus and Mold, Simple Parasites, Complex Parasites, Body Sites and Biotech, and Infrastructure.

Every few days you create using the provided utility a set of presets using a full system scan plus you specify your current section of the protocol. 

If you haven’t already, install Morgellons and Lyme Graded Utility as described in Installing Morgellons and Lyme Graded Utility. Double-click the Morgellons and Lyme Graded Utility icon to start Morgellons and Lyme Graded Utility. Before you use Morgellons and Lyme Graded Utility for the first time, you need to understand an overview of the protocol.

Continue reading →

Installing Morgellons and Lyme Graded Utility

Posted on by
Reply

Before you install Morgellons and Lyme Graded Utility, you must have .NET Framework 3.5 installed. Download the Morgellons and Lyme Graded Utility installer by clicking the Download link to the below.

DescriptionLink
Morgellons_and_Lyme_Graded_Utility_Setup.exe.zipDownload
GUIDE_M_L_Graded_Single_-_Click_Me.pdfDownload
Continue reading →

BFBTool Guide

Posted on by
Reply

The BFBTool provides a context for creating your own protocol for a particular disease. In your custom protocol you can specify a general purpose full system scan, a specific scan that targets a specific area, and a targeted preset for the specific disease. The BFBTool really helps the user who only has one or two generators, multiplexing the generators to do multiple programs, and in the case of Remote operation, multiple simultaneous programs on a single generator.

The process of creating presets to run the scan results of your Spooky2 Biofeedback scan can be quite cumbersome, especially if you are taking advantage of the fast GeneratorX scan rates and doing biofeedback scan on a frequent basis. The BFBTool automates the process of creating presets for the following hardware transmission modes: Remote, Contact, Plasma, Scalar, Laser, and Coil. There is a preference you can set to only generate a subset of these six transmission modes.

Continue reading →